Eldar Warlock on Jetbike

This tutorial is dedicated to those who shall not be named; Eldar players. There are a number of people who want to field jetlocks but don’t know how to make them.

It made with minimal sculpting in mind, while still making the final result look very much like a warlock.

  • 1 Eldar Warlock with Witch Blade and Shuriken Pistol (Part Code: 99060104122 )
  • 1 Eldar Jetbike
  • 1/16 inch brass rod
  • A Dremel or other rotary tool with cutting discs
  • Safety Goggles
  • Dust Mask
  • Modeling Knives (with a regular blade and a chisel blade)
  • Modeling Putty
  • Super Glue
  1. First, you will have to cut your warlock in half. Put a cutting disc on your Dremel, don your safety goggles and dusk mask, and make cuts where shown. I start with the cut separating the sword from the base, to get a feel for how the Dremel handles while cutting the pewter. Then I make another cut going from back to front, below the belt. Err on the side of cutting too low, you can always trim it later. Once this is done, clean up the area around the cuts with a modeling knife.

    Eldar Warlock Jetbike conversion

    Eldar Warlock Jetbike conversion

  2. Next part to go is the hands. Cut off the hand with the pistol using the chisel blade. The sword is a bit more difficult though. Since it is partially attached to the sleeve, you will have to carefully cut the sword’s hilt off of the sleeve before cutting the hand off. Slide a strong blade in between the sword and the sleeve and slowly cut it. It seems crazy but it will work.

    Eldar Warlock Jetbike conversion

    Eldar Warlock Jetbike conversion

  3. Now his arms have to come off. However, you need to make sure that the shoulder pads stay attached. To do this, I used the chisel blade in my modeling knife and made cuts from both sides, working my way inward.

    Eldar Warlock Jetbike conversion

  4. Cut the hand off of the sword. Glue the sword onto a one inch long piece of the brass rod. Either glue the pommel of the sword onto the other end, or make one using putty. Now we have a singing spear, which every jetlock should be equipped with.
    warlock jetbike conversion
  5. Glue together the entire bike except for the the rider, the flag-pole, and the carapace.

    warlock jetbike conversion
  6. Place, but do not glue, the rider’s legs on the jetbike. Having done this, figure out the angle at which you will put the warlock’s torso on. You will need to angle it so that the left arm is about three-quarters of a millimeter away from the left handle-bar. This will be the hand that holds the jetbike. You will have to file or cut the warlock’s belt pouch off for a clean fit.
  7. Having determined those angles, glue the warlock’s left arm in place. Remember that the wind should be pushing the sleeve backwards.

    warlock jetbike conversion
  8. Glue the warlock’s other arm on. It looks best raised to about head height.

    warlock jetbike conversion
  9. Once those have dried, fill the gaps on the arm joints with modeling putty and smooth it out with a sculpting tool or the back of a knife. Remember to keep your hands and tools wet when working with the putty.
    warlock jetbike conversion
  10. OPTIONAL: Some people like robes around their jetlock’s legs, and some don’t. If you like them, follow this step. If you don’t skip to the next step. Flatten some modeling putty until it is very thin, and then cut out a triangle. Place it so that one point of the triangle is over where the body will be glued on, and fold it around the leg. The whole piece should be swept backwards from the wind. Fold up the inside corner a bit. After the first side is satisfactory, repeat on the other side. Remember, if the warlock is a man it should be left over right, if a woman, right over left. I’m anal retentive, I know. Fit the legs onto the jetbike. You may have to bend your robes a little to make room for the engines.

    warlock jetbike conversion

    warlock jetbike conversion

  11. Glue the legs onto the jetbike, and then the body onto the legs. Remember to make room for the left hand.
  12. Cut the hands off of the jetbike rider’s arms and glue the left hand onto the left arm and the jetbike handle, and the right hand around the spear. Once the spear is dry, glue that hand to the body.
    Eldar Warlock Jetbike conversion
  13. Let it dry overnight, paint it pretty, and post it on the web.

REF: A forum somewhere in 2009.